This paper presents the design and implementation of a printed circuit microwave band-pass filter for 5G mid-band applications, using a Stub Loaded Multiple Mode Resonator (SL-MMR) technique. The objective of this article is to introduce a low-cost microstrip filter with improved passband&#x...

In the introduction of the presented work, the physical nature of the collapse of electrical energy transmission systems due to the influence of a magnetic storm is recalled. A mechanism is described by which, due to the non-linearity of the magnetic circuit of the system'...

Digital twins are the most important parts of Cyber-Physical Systems (CPSs), and play a crucial role in the realization of the Metaverse. Therefore, two important factors: flexibility and adaptability, need to be focused on digital twinning systems. From a virtual perspective, constructing&#...

This paper presents the gamma-ray detection performance of the newly developed MAPD-3NM-II type SiPM sensor array (4 [Formula: see text] 4) with [Formula: see text](Ce) scintillator. The gamma-ray spectra of various sources have been measured in the energy range from 26 keV up to&#...

The paper is concerned with the parameter study of a new generation of micro-pixel avalanche photodiodes (MAPD) with deeply buried pixel structure, also named silicon photomultipliers (SiPM) or multi-pixel photon counter (MPPC). The new MAPD of type MAPD-3NM was manufactured in the fram...

Timepix3 pixel detectors have demonstrated great potential for tracking applications. With 256 × 256 pixels, 55 μm pitch and improved resolution in time (1.56 ns) and energy (2 keV at 60 keV), they have become powerful instruments for characterization of unknown radiation fields. A...

In the last two decades, in search for savings, new technologies for steel processing have begun to be developed, which would bring improvements in performance according to the requirements of designers and specific applications. The driving force was the automotive industry, which, in&...

A series of experiments was conducted by quenching and partitioning (Q-P) heat-treated alloys to investigate the effect of cooling intensity on the mechanical properties of low alloy steel 42SiCr. By applying a conventional heat treatment, reasonable high strength can be achieved; however,&#...

The use of asphaltic concrete cores for sealing embankments and rockfill dams is very important. The self-healing properties of bitumen, simple construction in cold and rainy conditions compared to clay cores, good flexibility and connection with embankment materials are the essential charac...

This paper presents a printed magnetic probe that can switch from broadband to tunable narrowband for near-field measurement. In the early design stage, we created a printed loop gap resonator as a magnetic reference sensor for the pre-compliance test in a band up to 6 GH...

This paper introduces a methodology to investigate controlled switching (or "Point on Wave Switching") to reduce magnetizing inrush current in Transformer. When transformer is switched on, transformer will get energized and transiently, large current flows through the primary winding. This&#...

We report the results of the measurements of three pieces of the new Photonis miniPLANACON microchannel-plate photomultipliers (MCP-PMTs) intended for use in the demanding environment of the Large Hadron Collider (LHC) beamline as a part of the AFP Time-of-Flight detector. These photomultipl...

This paper deals with the movement, localization and navigation possibilities of Autonomous Robotic Platform (ARP). Such a platform is used for ADAS (Advanced Driver Assistance Systems) testing in automotive. At the beginning, the paper discusses different solutions that are already available...

A search for exclusive two-photon production via photon exchange in proton-proton collisions, pp→pγγp with intact protons, is presented. The data correspond to an integrated luminosity of 9.4 fb−1 collected in 2016 using the CMS and TOTEM detectors at a center-of-mass energy of 13 ...

This article presents the design, modeling, and fabrication of a printed log-periodic biconical dipole array antenna (PLPBDA) for electromagnetic compatibility (EMC) measurements. The proposed structure used bow tie-shaped dipoles instead of typical dipoles to achieve a size reduction of 50% and&...

This article proposes a new branch-line coupler design using two trapezoid-shaped resonators, applied in side and center. The standard 35 and 50 Ohms λ/4 transmission lines (TLs) are attained through the variations of the resonator’s TLs width. Since there are not explicit formulas...

We describe an analysis comparing the p¯p elastic cross section as measured by the D0 Collaboration at a center-of-mass energy of 1.96 TeV to that in pp collisions as measured by the TOTEM Collaboration at 2.76, 7, 8, and 13 TeV using a model-independent approach. The...

Events where the two leading jets are separated by a pseudorapidity interval devoid of particle activity, known as jet-gap-jet events, are studied in proton-proton collisions at √s=13 TeV. The signature is expected from hard color-singlet exchange. Each of the highest transverse momentum...

Measurements are presented of the single-diffractive dijet cross section and the diffractive cross section as a function of the proton fractional momentum loss ξ and the four-momentum transfer squared t. Both processes p p → p X and p p → X p , i.e. with the pro...

The TOTEM collaboration at the CERN LHC has measured the differential cross-section of elastic proton–proton scattering at s√=8TeV in the squared four-momentum transfer range 0.2GeV2<|t|<1.9GeV2. This interval includes the structure with a diffractive minimum (“dip”) and a secondary maximum (“bu...